Super User

Super User

The MTD-20KWe digital earth tester allows for the measurement of Earth Resistances and Soil Specific Resistivity, and also the spurious voltages caused by parasitic voltages present in the soil.

This equipment is suitable for fast and easy measurement of the grounding resistance in house and industrial buildings, hospital installations, lightning rods, antennas, substations, etc. Soil resistivity measurement allows for soil stratification in order to optimize the most complex grounding systems engineering.

Its state-of-the-art system of active and passive filters provides it with high immunity to electric interferences, making it possible to obtain reliable measurements even in the presence of spurious voltages, such as the ones that can be found in some urban areas and near primary substations.

A 1,470 Hz internal generator injects alternated current on the soil through an auxiliary rod. The voltage generated over the earth resistance is measured by the apparatus, and the resistance value is evaluated. The test current is automatically regulated.

Features

  • 3½ digits display
  • Earth Resistance measurement
  • Spurious voltage measurement
  • Resolution: 0.01 Ω
  • Resistance reading: up to 20 kΩ
  • Audible signal indicates anomalies in the current circuit

Specifications

Specifications   
Measurement ranges

Resistance: 0-20 Ω; 0-200 Ω; 0-2,000 Ω; 0-20 kΩ

Tension: 0-200 V~.

Accuracy

Resistance measurements:

± (2% of the measured value + 1% of the maximum value of the selected range).

Voltage measurements:

± (2% of the measured value + 1% of end of scale value).

Reading resolution

0.01 Ω in the resistance measurement. 

0.1 V in the voltage measurement.

Output power and current The output power is less than 0.5 W, and the output current is limited to less than 15 mA (Peak to peak).
Audible alarm It warns the operator in case that there are abnormalities in the current circuit, which make it difficult to obtain a reliable result.
Battery charger A smart, microprocessor controlled, circuit adjusts the battery charge to the optimised parameters in order to ensure the maximum service life. It is supplied by means of an external AC adapter (provided with the equipment) or from a 12 V car battery.

The MI-15KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 15kV. 

It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 3,000,000 MW with four test voltages: 1 kV - 5 kV - 10 kV and 15 kV. 

Readings are performed through an easy-toread analogue indicator, having a broad scale.

Due to its reduced size and weight, its power autonomy and mechanical strength, this insulation tester is suitable for working out in the field, under severe weather conditions. It is powered with a rechargeable battery, with a charger for 110 V/220 V. In order to protect the equipment, the cabinet is water and dust resistant. Protection grade is IP54, and the insulation tester is supplied with a complete kit of high voltage test leads.

Features

  • Insulation test up to: 3 TΩ
  • 4 Test voltages: 1 kV - 5 kV - 10 kV - 15 kV
  • Guard terminal
  • Rechargeable battery
  • Multiple scales for precision improvement
  • IP-54 Protection

Specifications

Specifications  
Test voltages 1 kV - 5 kV - 10 kV - 15 kV.
Maximum resistance reading

200 GΩ @ 1 kV.

1 TΩ @ 5 kV.

2 TΩ @ 10 kV.

3 TΩ @ 15 kV

Short circuit current 1 mA.
Test voltage accuracy ± 2% of nominal test voltages on R ≥ 10 GΩ.
Internal current limiting resistance

1 MΩ @ 1 kV.

5 MΩ @ 5 kV. 

10 MΩ @ 10 kV.

15 MΩ @ 15 kV.

Insulation tester Accuracy Class 2 (±2 % of full scale deflection).
Analogue indicator Up to 98 mm scale length, taut band, with mirror.

The MI-20KVe High-Voltage insulation tester is a truly portable device that allows the measurement of insulation resistances using test voltages up to 20 kV.

It employs a state-of-the-art technology for the safe measurements of insulation resistances up to 4,000,000 MΩ with four test voltages: 5 kV - 10 kV - 15 kV and 20 kV.

Analogue indicator, having a broad scale.

Due to its reduced size and weight, its power autonomy and mechanical strength, this insulation tester is suitable for working out in the field, under severe weather conditions. It is powered with a rechargeable battery, with a charger for 110 V/220 V. In order to protect the equipment, the cabinet is water and dust resistant. Protection grade is IP54, and the insulation tester is supplied with a complete kit of high voltage test leads.

Features

  • Insulation test up to: 4 TΩ
  • 4 Test voltages: 5 kV - 10 kV - 15 kV - 20 kV
  • Guard terminal
  • Rechargeable battery
  • Multiple scales for precision improvement
  • Portable, accurate & rugged
  • IP-54 Protection

Specifications

Specifications   
Test voltages 5 kV - 10 kV - 15 kV - 20 kV.
Maximum resistance reading

1 TΩ @ 5 kV. 

2 TΩ @ 10 kV. 

3 TΩ @ 15 kV. 

4 TΩ @ 20 kV.

Short circuit current 500 µA.
Test voltage accuracy ± 2% of nominal test voltages on R ≥ 10 GΩ.
Internal current limiting resistance

10 MΩ @ 5 kV.

20 MΩ @ 10 kV.

30 MΩ @ 15 kV.

40 MΩ @ 20 kV.

Insulation tester Accuracy Class 2 (±2 % of full scale deflection).
Analogue indicator  Up to 98 mm scale length, taut band, with mirror 

The Megabras MD-5060x is a smart, microprocessor-controlled, 5kV insulation tester and analyzer. Besides the conventional measurement of insulation resistances up to 5 TW, its advanced features allow to automatically measure both the Polarization Index and Dielectric Absorption Index, thus significantly simplifying testing of transformers.

This insulation tester is a portable, battery-powered equipment. Test voltage may be chosen from 500V to 5 kV in 100 dddV increments. Due to its measurement principle (actual voltage and current readings) the accuracy of resistance measurement is not affected by any test voltage error. Nevertheless, the High-Voltage generator is electronically stabilized with a better than 2% accuracy in open-circuit condition and for any normal operation battery voltage.

The MD-5060x is powered using a rechargeable battery and has an automatic charger that may be connected to 100 - 240V mains supply. The cabinet is strong and lightweight, easy to carry, impact-resistant and suitable to be used under severe weather conditions. Thus the megohmmeter supplies very reliable and accurate measurements both in laboratory and out in the field.

Features

  • Insulation resistance
  • Auto-range
  • Guard terminal
  • Automated tests:
    • Absorption index
    • Polarization index
  • Real time clock
  • 4000 Readings memory
  • USB Interface
  • Programable pass-fail
  • Built-in printer
  • Rechargeable battery

Specifications

Specifications  
Test Voltages

500 V, 1,000 V, 2,500 V, 5,000 V directly, one button selectable

500 V to 5 kV in 100 V increments.

DC, negative.

Maximum resistance reading 5 TΩ @ 5 kV.
Short circuit current 1.5 ± 0.5 mA.
Megohmmeter basic accuracy ± 3% of nominal test voltages on 10 GΩ.
Advanced features

Automated Polarization Index calculation.

Automated Dielectric Absorption Ratio calculation

Programmable Pass-Fail test.

Step Voltage Test.

Built-in printer Prints elapsed time, actual voltage and resistance measured each 15 seconds.

CRM 100B directly measures micro-ohm values at 100 Amps DC under live switchyard conditions.

CRM 100B is specially designed to reliably measure contact resistance of circuit breakers, isolators, busbar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards upto 765 kV.

Inbuilt rechargeable battery tremendously enhances utility as AC supply connectivity is not required.

CRM 100B operates on a rechargeable battery as well as Mains supply. It has a built-in constant current source, a precision instrumentation amplifi er, digital readout and control logic.A pulse of 100A DC is passed through the test object and voltage drop is sensed using the classical Kelvin’s 4 wire method to measure contact resistance. Both test current and resistance value are displayed on LCD.

Features

  • A radically new design makes CRM the lightest available contact resistance meter.
  • Battery as well as Mains operated.
  • Direct display of micro-ohm value does away with manual calculations.
  • Fool-proof connections and repeatability are ensured by
  • SCOPE’s specially designed proprietory Ck clamps.
  • Supplied with rugged calibrated test lead set suitable for 4 wire measurement.

Specifications

  • Ranges : 199.9μΩ and 1999μΩ
  • Resolution : 0.1μΩ and 1μΩ
  • Accuracy : Value ± 2 % ± 1 digit
  • Current : 100 A DC
  • Displays : Two, 3½ digit, ½ inch LCD, for current and
  • resistance values
  • Power : 230 V AC ± 15%, 50 Hz ± 10%, 75 VA
  • Battery : Instrument operation on inbuilt
  • rechargeable battery (2 nos. 6V, 4.5AH)
  • Dimensions : 435 x 350 x 170 mm
  • Weight : 9 kg, instrument
  • Environment: 0° to 50° C max, 95 % RH (non-condensing), Live EHV switchyard environment

 

Page 7 of 7